{"product_id":"auto-adaptable-controller-kg6-1100s","title":"AUTO-ADAPTABLE CONTROLLER KG6- 1100(S)","description":"\u003ch3 class=\"p1\"\u003e1. Characteristic\u003c\/h3\u003e \u003cp class=\"p1\"\u003eAuto-adaptable pump controllers can work under conditions of various pressures and replace the traditional system made up of a pressure tank, a pressure switch, a water shortage protection device, a check valve, a four-way junction, and a timer.\u003c\/p\u003e \u003ch3 class=\"p1\"\u003e2. Function\u003c\/h3\u003e \u003cp class=\"p1\"\u003eAuto-adaptable pump controllers, which need only to be plugged in to work, automatically adjust according to different pressures of pipes, and different heights of floors, buildings ranging in height from zero to one hundred meters. It boasts of such advantages as water shortage protection, water shortage self-check, start-up upon water supply, pressure adjustment start-up, timing (optional), lightning protection, and overvoltage and under-voltage protection.\u003c\/p\u003e \u003ch3 class=\"p1\"\u003e3. Installation\u003c\/h3\u003e \u003cul\u003e \u003cli class=\"p1\"\u003eAuto-adaptable controllers must be installed by professionals fully informed of general mandatory safety regulations. At the same time, water must be kept clean, and the pump must operate normally.\u003c\/li\u003e \u003cli\u003eThe controller must be installed next to the outlet side of the pump, and the tap must be fixed not between the controller and the pump, but after the controller is fixed.\u003c\/li\u003e \u003cli\u003eThe controller does not work if glue or residue is left in it. \u003cp class=\"p1\"\u003eAnd it must be installed vertically.\u003c\/p\u003e \u003c\/li\u003e \u003cli\u003e \u003cp class=\"p1\"\u003eIt is recommended that the controller and the pump should have a set of sockets and switches of their own. Three-core cables with an outer diameter section of 7-8 mm x 1.5 mm should be used to connect the controller with the pump, and the testing lines of the controller must be used, and its power supply must be guaranteed to be up to standard.\u003c\/p\u003e \u003c\/li\u003e \u003c\/ul\u003e \u003ch3 class=\"p1\"\u003e4. Wire connection\u003c\/h3\u003e \u003cp class=\"p1\"\u003ePlease open the upper cover and connect the wires according to diagram 2. After wiring, please lock the screws on terminals L\/N\/E \u0026amp; UNW as well as the four screws on the base (bottom cover).\u003c\/p\u003e \u003ch3 class=\"p1\"\u003e5. Button instruction\u003c\/h3\u003e \u003cp class=\"p1\"\u003eAfter installation of the controller and pump, please open the valve (faucet), then plug in the controller; the pump starts working. When “Power on, Pump on, Flow (on)” three indicators all light on, close the valve, the pump stops working. Here, the controller completes the first learning.\u003c\/p\u003e \u003cp class=\"p1\"\u003eAfter a few seconds, the pump starts working again. “Power on” and “Pump on” indicators light up, and then the pump stops working. Here, the controller completes the second learning and finishes the setting of the starting pressure.\u003c\/p\u003e \u003cp class=\"p1\"\u003eHereinafter, the pump will automatically start and stop according to the switch of the valve.\u003c\/p\u003e \u003col\u003e \u003cli\u003e“Auto\/Reset”: Press this button to exit water shortage protection or frequent start \u0026amp; stop protection. Or when the working condition changes, the original starting pressure is not suitable for working, press this button to relearn the pipeline pressure and reset the starting pressure.\u003c\/li\u003e \u003cli\u003e“UP+”: it’s for manual operation to increase the starting pressure of 1.0 bar per press\u003c\/li\u003e \u003cli class=\"p1\"\u003e“DOWN”: It’s for manual operation to decrease the starting pressure by 0.1-0.2 bar per press.\u003c\/li\u003e \u003cli\u003ePower on: It means there is electricity going through the controller.\u003c\/li\u003e \u003cli\u003ePump on: It means the pump is working.\u003c\/li\u003e \u003cli\u003eFlow (on): It means there is water going through the controller.\u003c\/li\u003e \u003cli\u003eWater shortage (flash): When the water shortage indicator flashes, it means water shortage protection has been triggered.\u003c\/li\u003e \u003cli\u003eAuto\/Reset (flash): When the Auto\/Reset indicator flashes, it means the frequent start-and-stop protection has been triggered.\u003c\/li\u003e \u003c\/ol\u003e","brand":"Monster Mechanical","offers":[{"title":"Default","offer_id":45115701297221,"sku":"KG6-1100(S)","price":343.62,"currency_code":"ZAR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0739\/8627\/7445\/files\/AUTO-ADAPTABLE-CONTROLLER-KG6-1100S.jpg?v=1780903162","url":"https:\/\/www.monstermechanical.co.za\/products\/auto-adaptable-controller-kg6-1100s","provider":"Monster Mechanical","version":"1.0","type":"link"}